Tag Archives: mock-up

New Branch Up-and-Running

Kemmergem Tipple Mock-Up
Newly completed Kemmerer Gem No.2 tipple mock-up on the Gin Creek Branch

I’ve been working feverishly on the Gin Creek Branch which served the distinctive two-track loader at Kemmergem, VA. This branch occupies about 1/3 of my upper deck and is the first piece of the upper deck to be operational. I went out of my way to make the trackwork look like a well-used and minimally maintained branch with some crooked ties and rail. This branch is also laid out on an S-curve where you can look all the way down the straight portion where the loader will lie between the curves, and because of this curve, I think this might become the “signature scene” for the layout.

First Train on Upper Deck
Here’s the first train on the upper deck rolling through the junction onto the Gin Creek Branch at Turners Siding

 

First Train on Upper Deck
The tail track just barely holds two GP38s and two triple hoppers

To get things operational, I had to run the DCC bus wires and install manual switch mechanisms. At this point, I was able to run the first train to the upper deck and make sure everything worked. It’s a cool arrangement with double-ended loader tracks but a short tail track that barely holds two GP38s and two triple hoppers. I’ve also installed a stub track alongside the tail track for the Ralph Baker coal company that built a truck dump here in the late ’70s / early ’80s. Since I’m currently running the ’60s, I decided to use the track to house a small ramp-style loader (which will be replaced by Ralph Baker in late ’70s ops sessions). Switching the track arrangement is a lot of fun and requires some extra thinking since the spur to Ralph Baker is a facing-point stub track, and the only run-around is under the Kemmerer Gem No.2 tipple. You’ve got to place the cars for Ralph Baker and the cab behind the empties for the big tipple and then push them into the right tracks using the loads and empties under the big tipple.

Kemmergem Tipple Mock-Up
View of the south end of the loader at Kemmergem

While it was “operational,” there was still no tipple, and the switches had to be thrown by reaching far under the layout. With an upcoming ops session, I was motivated to give it a bit more finish, so I cut and painted the fascia and put in the switch controls. I also took the opportunity to install my fast-clock controls in their permanent place, a little cut-out in the fascia. What’s a mine run without a loader, so I created another temporary “paper doll” mock-up from cardstock prints and foamcore for the Kemmerer Gem No.2 tipple. This is a really cool looking loader that has two loading points with a long covered conveyor between them making the thing look a bit like a corrugated diplodocus dinosaur. I created some drawings of a slightly compressed version based on a series of photos from the ’50s-’90s (it didn’t change too much) including some great detail shots by Robby Vaughn. While I was at it, I created a little temporary dock for the Ralph Baker spur (which I’m calling “Darbyville Dock” for the ’60s sessions). A couple of paint brush handbrakes on the steeper spotting locations, and the branch was ready for an ops session!

Kemmerer Gem 2 1998
The prototype Kemmergem tipple shot by Robby Vaughn in the late ’90s

 

Kemmergem Tipple Mock-Up
Gluing the prints onto foamcore for the tipple

 

Kemmergem Tipple Mock-Up
Mock-up for one of the two loading points waiting for a paper roof

 

Darbyville Dock
Mock-up of “Darbyville Dock” at the end of the Gin Creek Branch–note the gnarly trackwork on the tail track to the right

 

Fast Clock Controls
Here’s the finished fast-clock control panel recessed into the upper deck fascia.

More Coal Loader Mock-Ups

Coal loader mock-ups in St Charles
Here’s the full mocked-up scene with the St Charles Switcher preparing to swap empties for loads at the JAD Turner loader–the St Charles loader can be seen just around the hillside

As I’ve discussed previously, I like to build mock-ups out of foam core and paper of the larger structures on the layout that I will eventually scratchbuild. This serves three purposes. First, it gives me an opportunity to create a line-drawing / blueprint and make sure the drawing works before cutting more expensive materials. Second, it allows me to visualize a scene and make adjustments before I build the permanent structure. And third, it gives me a good stand-in on the layout until I can build the real one–something that makes operations a lot more fun than imagining there’s a big structure where you’re switching! For this third reason, I put a little extra effort into the drawings to give them some color and texture. I’ve covered the techniques before, so I won’t repeat them here.

This project involved the two “truck dump” tipples that were built in the late ’70s (as far as I can tell) near St Charles, VA. One is known as JAD Turner, and it’s probably still standing today. The other sat on the wye at St Charles for just a few years–I don’t know it’s name, so I’m just calling it the St Charles loader (super original, I know…). What made this project challenging is I didn’t have any good photos of the loader configuration I needed to model. JAD Turner was modified over the years with a second conveyor and second empty track, but the earliest photo I have of it (a grainy aerial from 1981) clearly shows only a single conveyor. I’m modeling it as if it’s the same tipple but with fewer added parts, so I took the dump shed / crusher section of the current loader along with a single conveyor and came up with this design that looks reasonably close to the aerial.

JAD Turner Tipple
Here’s the JAD Turner loader near St Charles in the late ’90s with additional chutes added, but I modeled the core dump shed, crusher, and one of the conveyors (Robby Vaughn photo)
JAD Turner loader mock-up
Here’s the finished JAD Turner loader mock-up complete with a little double chute over the rails

St Charles was a little more challenging as the ONLY photo I have is a grainy aerial from 1981 showing what looks like a pile of coal, a conveyor (maybe two), and what looks like a dump ramp but no shed. I didn’t have to look far to find something close. Just up the road between St Charles and Mayflower was a loader known as “Southwest” which had a similar dump and conveyor arrangement. Southwest was built after my era, so I won’t have to have two similar looking loaders on the layout. Who knows, perhaps they moved the loader from St Charles up to Southwest? That’s my story until someone proves otherwise…

Southwest Loader near St Charles
The Southwest loader sat between St Charles and Mayflower but after my era–I’m using it as the prototype for my St Charles loader (Robby Vaughn photo)
St Charles loader mock-up
A view of the St Charles loader mock-up showing the ramp and dump area

Anyway, here are the results, and I’m really liking the scene now. I can’t wait to build the real things! But first the upper deck…